babyhood Ergonomic Cot
The babyhood Ergonomic Cot is better for your back and is a unique baby Cot. The babyhood ergonomic cot was designed specifically to reduce the stress placed on carers and mums.
This has been done by increasing the base height and making access to the child easier. The unique design of the babyhood Ergonomic Cot allows carers and mums to get closer to the child to reduce the impact of the load.
Why would you buy the Babyhood Ergonomic Cot?
1. The safest cot for you and your baby.
2. Better for you and your baby as it is sustainable with real clear grade NZ plantation timber.
3. Ergonomically designed to save your back with babyhood’s famous smooth single hand drop side with extra safety latch.
4. Grows with your child as the base levels adjust from bassinet to cot.
5. Safer for your baby with BPA free teething rails that are very discreet.
6. Available in Baltic.
7. Easy to maneuver around your nursery with 4x lockable heavy duty castors which are perfectly suitable for an evacuation cot.
8. 1200mm x 600mm internal dimensions.
9. Tested to AS/NZS 2172:2003 and complies with AS/NZS 2172:2010 – Australian Standard for Domestic use Cots as well as the Commercial Tip Test Standard.
10 .This cot is tested by the highly regarded NATA accredited testing facility AFRDI (Australian Furnishing Research and Development Institute) to ensure that the cot is safe and meets with the Standards noted above.
Why did babyhood create a specific Cot for this industry?
Work Safe Victoria discovered carers were suffering from multiple skeletal injuries. These were caused by the repeated manual handling and bending into cots in 2011. The injuries caused varied from person to person but are caused primarily by the repeated bending into lower level cots.
Work Safe Victoria proceeded to issue Early Learning Centre’s infringement notices and required center’s to change their cots to a more suitable cot to reduce the injuries caused.
This meant that the options for Early Learning Centre’s were limited to Cots that did not meet Australian Standards or metal cots. Metal Cots didn’t meet the comfort and assurance requirements of parents and carers.
As a result, babyhood began working in consultation with various associations including Work Safe Victoria, Kindergarten Parents Victoria (KPV), Good Start Childcare, Fair Trading Victoria, Fair Trading Queensland and one of Australia’s leading ergonomists Chris Fitzgerald.
babyhood decided to try to resolve the issue by developing a Cot specific for this industry’s needs. This was no easy task as it required new innovation, new technology and the consensus of all the related parties as to what was best for carers, babies and parents.
After almost 14 months, babyhood had designed and manufactured the babyhood Ergonomic Cot, which was proudly launched at the KPV Conference in Melbourne.
The unique Australian Patented and Design Registered Cot was designed to reduce the stress placed on carers. They did this by increasing the base height and making access to the child easier. The design allows carers to get closer to the child to reduce the impact of the load.
Standards and Regulatory Requirements.
The babyhood Ergonomic Cot is tested to AS/NZS 2172:2003 and complies with AS/NZS 2172:2010 – Australian Standard for Domestic use Cots as well as the Commercial Tip Test Standard. The cot is tested by the highly regarded NATA accredited testing facility AFRDI (Australian Furnishing Research and Development Institute) to ensure that the cot is safe and meets with the Standards noted above.
|Carton 1||150cm x 71cm x 10cm|
|Carton 2||128cm x 78cm 13cm|
|Assembled||155cm H x 127cm L x 68cm W – Base from floor 75cm without castors 85cm with castors|
|Mattress Size||120cm x 60cm x 10cm|
|Pillow And Mattresses Size||1200mm * 600mm * 100mm|
Watch the Video Below Now: